Search For How To Catch A Fish at Amazon
|
Using a fish finder to locate fish is not difficult, but it does take a lot of exercise and galore getting used to. The initial thing to do after buying a fish finder is obvious- Read the Manual! The manual may not be stimulating or may have more technical selective information than you are mesmerized in reading, but it can not be stressed sufficient how essential it is to read the manual in order to acquaint yourself with the unit you purchased. The next thing to do will be to mount your fish finder. Whether you are using a transom mount, trolling motor mount, hull mount or a portable mount, your manual will be capable to walk you through the steps to the right way mount your model. If in doubt, consult a professional or have a professional mount it for you. Now you are ready to turn on your fish finder and get ready to catch more fish. When you basi turn the unit on, it will be in automatic mode, meaning that the pre-programmed settings will be in use. As you become more intimate with your model, you will be capable to switch to manual mode and custommake the settings to the fishing conditions you experience. To begin, leave the fish finder on automatic and take a five minute spun around the lake, bay or ocean that you fish in. Watch the display perpetually to get a feel for what you see. Don’t worry in regards to catching fish or understanding everything on the display yet. That will come with experience. Now get started adjusting one feature at a time and become intimate with that feature. One of the key settings to play around with is the Sensitivity setting. When you adjust the unit’s sensitivity you are adjusting the power of the fish finder. The simple rule of thumb is, the lower the power (sensitivity) the lower the quality of the view on the display. Experts commend setting the sensitivity to amidst 75 and 100%. Trial and error will be the best way to determine the optimal setting for your model. The next setting to visit in manual mode, is the Fish ID setting. Once you have a feel for your unit, turn off the Fish ID feature and undertake to get used to reading the fish arches that you will see naturally on the screen. The fish icons displayed by the Fish ID are utile for unfeigned beginners, but once you start out to acquaint yourself with the display it is better to learn how to read the natural fish arches. The fish arches will give you a more precise view of what is beneath water. Another feature, Auto Depth, is best employed at it is pre-programmed setting as you get started using your fishfinder. Using the pre-programmed setting will tell the unit to mechanically track the bottom and is best used when you are new to using sonar. As you become more of an expert, you may manually set the upper and lower limits of the display window. The littler the display window you set the better the solution will be. In general, expert anglers eliminate the top few feet of water and stop the scan in regards to ten feet underneath the true bottom. The display window size will of course vary depending on how deep the water is and what type of fish you are looking to catch. Experiment with the display window size until you are comfortable with both the amount of water you may view and the picture resolution. As you are getting more and more intimate with your fish finder, you will observe a horizontal line throughout the screen. This line is the Depth Cursor and may be moved up or down on the display. When you find a great deal of fish, adjust the depth cursor to cut through the fish arches and the unit will tell you incisively how deep those fish are. Now you recognise precisely how deep to drop your bait. One last feature to touch on in this article is the suppressor setting. This setting tells the unit how much “back ground” noise to filter out. Eliminating the back ground noise may be helpful, but if your transducer is mounted in the right manner it is in general unnecessary. If you find you have to use the suppressor to locate fish, then you ought to check that your transducer is mounted correctly. In general you want to have the suppressor off as having the suppressor setting too high may block the sonar signal completely and you won’t find fish that way! Using a fish finder may seem gorgeous daunting at first, but like anything else in life, it just takes practice. Don’t be affrighted to experiment with your model, try dissimilar settings, and see what happens. Trial and error will in the long run aid you tune your fish finder to the perfective configuration for your fishing experience. Before you recognise it you will locate more fish than you recognise how to catch. Good luck and have fun fishing!
Most helpful customer reviews 2 of 2 people found the following review helpful. |
A read-aloud treat to share between parents and children who love the sport and art of fishing.